[2022] Valid NACE-CIP1-001 test answers & NACE NACE-CIP1-001 exam pdf [Q14-Q32] : Free Exam Dumps Collection : http://free.examcollectionpass.com

NEW QUESTION 14
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

a recognized industry standard like SSPC-PA 2 that is broadly accepted

NACE 2/SSPC SP10

their best judgment based on similar projects and specifications.

a detailed checklist and document the lack of a standard.

NEW QUESTION 15
In the event of a conflict between the project specification and the coating manufactures’ product data sheet, the Inspector’s first course of action should be too:

Call the coating manufacturer for clarification

Use the product data sheet as a guide

Use the job specification as a guide

Call the person who wrote the specification for clarification

NEW QUESTION 16
Check abrasive blast pressure close to the

compressor

blast pot

blast nozzle

substrate

NEW QUESTION 17
NACE Level 1 Inspectors have been trained to perform:

All types of inspection

Visual inspection and Non-destructive testing

Visual inspection, Non-Destructive and Destructive testing

Visual inspection only

NEW QUESTION 18
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

105 Gauge Readings resulting in 35 Spot Measurements

75 Gauge Readings resulting in 25 Spot Measurements

225 Gauge Readings resulting in 75 Spot Measurements

45 Gauge readings resulting in 15 Spot Measurements

NEW QUESTION 19
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

True

False

NEW QUESTION 20
According to SSPC PA 2 a Spot Measurement is:

A single gauge reading

The average of gauge readings taken in a 4cm (1.5 inch) circle

The overall average of all readings

The average of all spot measurements in a given area

NEW QUESTION 21
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

Failing to determine the base metal reading (BMR)

Rotating the dial too fast when taking measurements

Taking measurements too far from the edge of a surface

Measuring ditty, tacky, or soft films

NEW QUESTION 22
In a non-convertible coating the role of the primary solvent is to:

To make the coating flow out better

To dissolve the resin

To promote faster cure

To control the evaporation rate

NEW QUESTION 23
The initial steel condition is important to the NACE Inspector because:

If the steel is pitted more coating will be required

Less abrasive is need if the mill Scale s gone

It affects the final appearance after blasting

The Inspector may have to reject the Steel

NEW QUESTION 24
Upon arrival of coating materials, the inspector should

review coating contractors’ plans for storage of coating materials and confirm they meet national, local and owners’ fire and environmental regulations.

observe and document the amount of material and batch numbers.

observe aryl document that the applicator WFT at regular intervals during application.

observe and document time frame and environmental conditions between each coat.

NEW QUESTION 25
Which one of the following documents is the best source for coating technical data:

Safety Data Sheet;

Technical Data Sheet

Application Guidelines

Specification

NEW QUESTION 26
Digital hygrometers

consist of a bimetallic sensing element protected from wind gusts.

are used to measure temperature from a distance.

use a thermocouple in contact with the surface to measure temperature

determine relative humidity, air temperature, and dew point temperature:

NEW QUESTION 27
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a

dry film thickness (DEI) measurement.

wet film thickness (WFT) measurement.

blotter test for the presence of oil and water.

vial lest.

NEW QUESTION 28
If inspectors identify issues of non-conformance during an inspection, they should

instruct the contractor’s personnel in how to correct the issue so the project is not delayed

perform additional tests secretly to ensure there are no other potential issues at the site

inform both the Contractor and the inspector’s supervisor so they can take appropriate corrective actions

wait until the final report is being prepared to identify the issues in writing so they are fully documented

NEW QUESTION 29
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called

cracking.

sagging.

holiday.

checking.

NEW QUESTION 30
Safety Data Sheets must be carefully reviewed by:

The Application personnel

The Inspection personnel

The Owner’s personnel

All personnel involved in the job

NEW QUESTION 31
Owners hire NACE Inspectors’ with the expectation that:

The inspection cost will be offset by an improvement in service life

The Inspector will improve job flow and schedule

The Inspector will make a meaningful technical contribution to the job

a) and c)

NEW QUESTION 32
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:

Break the blisters to see what’s inside

Document the problem and advise the Contractor and Owner’s representative

Document the problem and advise the Contractor

Extract any liquid that may be inside the blister and send it to the lab for further analysis

[2022] Valid NACE-CIP1-001 test answers & NACE NACE-CIP1-001 exam pdf [Q14-Q32]

For more info read reference: