This page was exported from Free Exam Dumps Collection [ http://free.examcollectionpass.com ] Export date:Wed Oct 23 7:22:16 2024 / +0000 GMT ___________________________________________________ Title: 2024 New Training Course D-SNC-DY-00 Tutorial Preparation Guide [Q11-Q34] --------------------------------------------------- 2024 New Training Course D-SNC-DY-00 Tutorial Preparation Guide Dumps of D-SNC-DY-00 Cover all the requirements of the Real Exam QUESTION 11What is the correct order of steps for data flow in asymmetric IRB frame encapsulation? Explanation:* Ingress VTEP performs a route lookup that is based on the destination IP address.* Ingress VTEP encapsulates the packet with VXLAN and sends it on the appropriate VNI segment.* Egress VTEP determines that the host is local to the VNI and switches the packet.* Egress VTEP bridges the packet after decapsulation.Steps and Correct Order:* Ingress VTEP performs a route lookup that is based on the destination IP address.* The ingress VTEP (Virtual Tunnel Endpoint) first needs to determine the next hop for the packet.This involves performing a route lookup using the destination IP address.* Ingress VTEP encapsulates the packet with VXLAN and sends it on the appropriate VNI segment.* Once the route lookup is complete, the ingress VTEP encapsulates the packet in a VXLAN header, which includes the appropriate VNI (VXLAN Network Identifier) segment, and forwards it.* Egress VTEP determines that the host is local to the VNI and switches the packet.* The egress VTEP receives the encapsulated VXLAN packet, decapsulates it, and then checks its local VNI to determine if the destination host is within the same VNI.* Egress VTEP bridges the packet after decapsulation.* After determining the destination host’s locality, the egress VTEP bridges the packet to the appropriate interface to deliver it to the final destination.References:* Dell Technologies Networking – SONiC* Dell Enterprise SONiC Deployment GuideThese steps provide a comprehensive guide to understand the correct order of operations in asymmetric IRB (Integrated Routing and Bridging) frame encapsulation within a VXLAN environment.QUESTION 12Configure the system to meet these requirements.. Configure R1 with AS 1.. R1 must use a static neighbor assignment for BGP peering.. R1 needs to redistribute all current and future connected IPv4 routes.All the required BGP configurations have already been completed on R2.R2 resides in BGP AS 2. see the explanation for all step by step solution with all explanation.Explanation:Here is the step-by-step configuration for R1:* Enter BGP Configuration Mode:R1# configure terminalR1(config)# router bgp 1* Configure the BGP Neighbor:R1(config-router)# neighbor 10.10.12.2 remote-as 2* Redistribute Connected Routes into BGP:R1(config-router)# redistribute connected* Exit BGP Configuration Mode and Save the Configuration:R1(config-router)# endR1# write memoryComprehensive Detailed Step by Step Explanation with References:* Enter BGP Configuration Mode:* To configure BGP on R1, you need to enter global configuration mode and then enter BGP* configuration mode with the AS number. Since R1 is in AS 1, you use the command router bgp 1.* Configure the BGP Neighbor:* BGP neighbors must be manually specified. In this case, R1’s neighbor is R2, which has an IP address of 10.10.12.2 and resides in AS 2. The command neighbor 10.10.12.2 remote-as 2 establishes this relationship.* Redistribute Connected Routes into BGP:* To ensure that all connected routes on R1 are advertised via BGP, you use the redistribute connected command. This ensures that any connected IPv4 routes are redistributed into BGP, meeting the requirement to advertise current and future connected routes.* Exit BGP Configuration Mode and Save the Configuration:* Once the configuration is complete, you exit BGP configuration mode by typing end and then save the configuration with the write memory command. This ensures that the changes persist after a reboot.References:* Cisco BGP Configuration Guide* Dell Technologies Networking – SONiC* Dell Enterprise SONiC Deployment GuideThese steps provide a comprehensive guide to configure R1 to meet the specified requirements for BGP peering and route redistribution.QUESTION 13How many port channels can be assigned to a single port?  8  2  4  1 According to the Dell SONiC documentation, a single physical port can be a member of only one port channel at a time. This restriction ensures the consistency and integrity of link aggregation configurations.References:* Dell Networking SONiC: How to Configure Port Channels* Dell Technologies InfoHubQUESTION 14Refer to the exhibit.What can be determined from this show command?  Traffic below 100 KB is marked as congested  ECN is enabled for all colors  ECN is enabled for all DSCP values  There is a 10% probability that traffic is marked as congested The output of the command show qos wred-policy pfc34 shows the ECN (Explicit Congestion Notification) configuration for the policy pfc34. The line ecn: ecn_all indicates that ECN is enabled for all traffic classes (all DSCP values). Additionally, the green-min-threshold, green-max-threshold, and green-drop-probability settings are shown, but there is no indication of a 10% probability for marking traffic as congested. Therefore, the correct answer is B.References:* Dell Enterprise SONiC documentation* Dell Technologies InfoHubQUESTION 15Create port channel 10 on interfaces Eth 1/11 and 1/12, so that it connects to an already configured switch. A server will be connected on Eth 1/1. Both the server and port channel need VLAN 1 untagged and only VLAN10 tagged.Complete the configuration on Switch A. see the explanation for all step by step solution with all explanation.Explanation:Here are the steps to configure the required port channel and VLAN settings on Switch A:* Enter Configuration Mode:SwitchA# configure terminal* Create Port Channel 10:SwitchA(config)# interface port-channel 10SwitchA(config-if-po10)# switchport mode trunkSwitchA(config-if-po10)# switchport trunk native vlan 1SwitchA(config-if-po10)# switchport trunk allowed vlan 1,10* Assign Interfaces Eth 1/11 and Eth 1/12 to Port Channel 10:SwitchA(config)# interface ethernet 1/11SwitchA(config-if-eth1/11)# channel-group 10 mode activeSwitchA(config-if-eth1/11)# exitSwitchA(config)# interface ethernet 1/12SwitchA(config-if-eth1/12)# channel-group 10 mode activeSwitchA(config-if-eth1/12)# exit* Configure Interface Eth 1/1 for Server Connection:SwitchA(config)# interface ethernet 1/1SwitchA(config-if-eth1/1)# switchport mode trunkSwitchA(config-if-eth1/1)# switchport trunk native vlan 1SwitchA(config-if-eth1/1)# switchport trunk allowed vlan 1,10SwitchA(config-if-eth1/1)# end* Save Configuration:SwitchA# write memoryComprehensive Detailed Step by Step Explanation with References:* Enter Configuration Mode:* Start by entering the global configuration mode to make changes to the switch configuration.* Create Port Channel 10:* Enter the port channel interface configuration mode using interface port-channel 10.* Set the port channel to trunk mode with switchport mode trunk.* Specify VLAN 1 as the native VLAN (untagged) using switchport trunk native vlan 1.* Allow VLANs 1 and 10 on the trunk with switchport trunk allowed vlan 1,10.* Assign Interfaces Eth 1/11 and Eth 1/12 to Port Channel 10:* Enter interface configuration mode for ethernet 1/11 and ethernet 1/12.* Assign each interface to port channel 10 using the channel-group 10 mode active command.* Exit the interface configuration mode.* Configure Interface Eth 1/1 for Server Connection:* Enter interface configuration mode for ethernet 1/1.* Set the interface to trunk mode with switchport mode trunk.* Specify VLAN 1 as the native VLAN using switchport trunk native vlan 1.* Allow VLANs 1 and 10 on the trunk with switchport trunk allowed vlan 1,10.* Exit the configuration mode.* Save Configuration:* Ensure the configuration is saved so it persists after a reboot using the write memory command.References:* Dell Technologies Networking – SONiC* Dell Enterprise SONiC Deployment GuideThese steps provide a comprehensive guide to configure a port channel and VLAN settings on Switch A to meet the specified requirements for server and trunk connections.QUESTION 16Refer to the exhibit.The route distinguisher was autogenerated. Which VLAN is mapped to VNI410?  VLAN 410  VLAN41  VLAN 10  VLAN 26 The route distinguisher (RD) in the exhibit is 10.0.2.26:41. The RD typically reflects the VNI and VLAN mapping configuration. Given that the VNI is 410 and the RD ends with :41, it implies that VLAN 10 is mapped to VNI 410.References:* Dell Technologies SONiC documentation* VXLAN Configuration GuideQUESTION 17Refer to the exhibit.What type of route is shown?  Type 3 host route from external VTEP  Type 2 host route from another VTEP  Type 3 host route from another VTEP  Type 5 host route from another VTEP The exhibit shows a BGP EVPN route in a VXLAN environment. The route type can be determined based on the details provided. Type 2 routes in BGP EVPN are used to advertise MAC address reachability information between VTEPs (Virtual Tunnel End Points). The exhibit indicates a host route from another VTEP, which corresponds to a Type 2 route.References:* Dell Technologies SONiC documentation* BGP EVPN Configuration GuideQUESTION 18Which network devices route unencapsulated user traffic in a symmetric IRB overlay network?  Leaf router and spine router  Source VTEP and destination VTEP  Autonomous system boundary router and source VTEP  Capability extended next hop router and leaf router In a symmetric Integrated Routing and Bridging (IRB) overlay network, the Source Virtual Tunnel End Point (VTEP) and the Destination VTEP route unencapsulated user traffic. Symmetric IRB ensures that routing occurs at both the ingress and egress VTEPs, allowing for optimized traffic flow and efficient network operations.References:* Dell Technologies SONiC documentation* VXLAN Configuration GuideQUESTION 19What is the purpose of the write erase boot command option?  Delete the startup and enable zero touch provisioning.  Remove user-installed packages and tile changes.  Delete the startup configuration and the management interface configuration.  Delete the running configuration and all user accounts. The write erase boot command option deletes the startup configuration and enables zero touch provisioning (ZTP). This is used to reset the switch to its default state and prepare it for automated configuration through ZTP.References:* Dell Technologies SONiC Command Reference Guide* Switch Configuration GuideQUESTION 20Refer to the exhibit.What is the primary VRRP router for VRRP group 10?  Router-1  Router-2  Router-3 Based on the exhibit, Router-2 has the highest priority (90) in VRRP group 10. In VRRP, the router with the highest priority becomes the primary (master) router. Therefore, Router-2 is the primary VRRP router for VRRP group 10.References:* Dell Technologies SONiC VRRP Configuration Guide* VRRP Protocol OverviewQUESTION 21An administrator obtains the following CLI output:How much time does the local system take to detect remote failures without receiving packets?  600 milliseconds  900milliseconds  1200 milliseconds  800 milliseconds The local timers in the BFD (Bidirectional Forwarding Detection) configuration show a detect multiplier of 4 and a receive interval of 300ms. The time taken to detect remote failures is calculated as detect multiplier × receive interval = 4 × 300ms = 1200ms.References:* Dell Technologies SONiC documentation* BFD Configuration GuideQUESTION 22An administrator issues The ztp enable and show ztp status commands. What two objectives are they trying to accomplish?  Administratively enable the ZTP process.  Remove the ZTP function from the switch.  Disable the ZTP process.  Check on the progress of the ZTP process. The ztp enable command is used to administratively enable the Zero Touch Provisioning (ZTP) process on the switch. This process allows the switch to automatically download and apply configuration files upon boot-up without manual intervention. The show ztp status command is used to check on the progress and status of the ZTP process, providing information about whether the process is active, completed, or encountered any issues.References:* Dell Technologies SONiC documentation* Dell Networking Configuration GuideQUESTION 23Which protocol is used to perform an automated installation of Enterprise SONiC?  HTTP  SCP  SFTP The automated installation of Enterprise SONiC is typically performed using the HTTP protocol. During the Zero Touch Provisioning (ZTP) process, the switch retrieves configuration files and software images from an HTTP server, allowing for automated and streamlined deployments.References:* Dell Technologies SONiC documentation* ONIE User GuideQUESTION 24An administrator for a service provider uses this command on a switch:What is the result of running the command?  Maps the VLAN traffic that a CVLAN identifies to a VNI on a VTEP  Maps the VLAN traffic that a TPID identifies to a VNI on a VTEP  Maps the VLAN traffic that an SVLAN identifies to a VNI on a VTEP The command interface vxlan vtep-stacking followed by map vni 10010 vlan 100 maps the VLAN traffic that an SVLAN identifies to a VNI on a VTEP. In this context, SVLAN (Service VLAN) is being mapped to a VXLAN Network Identifier (VNI) for encapsulation and transport across the VXLAN tunnel.References:* Dell Technologies SONiC documentation* VXLAN Configuration GuideQUESTION 25A deployment requires routing and dynamic access control lists. What bundle must be used for this deployment?  Enterprise Standard  Enterprise Standard  Edge Standard  Cloud Premium For a deployment that requires routing and dynamic access control lists, the appropriate bundle to use is the Enterprise Standard bundle. This bundle includes advanced routing capabilities and supports dynamic access control lists for comprehensive network management and security.References:* Dell Technologies SONiC documentation* Dell Networking Bundle Configuration GuideQUESTION 26What is a correct use-case scenario for ZTP in Enterprise SONiC?  The user wants single pane of glass monitoring.  The user wants multivendor switch deployment.  The user wants to configure the switch manually using the CLI.  The user wants to replace a failed unit and use an automatic script. QUESTION 27Enterprise SONiC Switch 1 and Switch 2 are part of a symmetric VXLAN fabric in a data center environment.Switch 1 has learned MAC addresses from its local VLANs.What role does BGP EVPN play in this scenario?  Distributes locally learned MAC addresses to Switch 2  Establishes Layer 2 connectivity between Switch 1 and Switch 2  Enables efficient communication across the VXLAN fabric BGP EVPN (Border Gateway Protocol Ethernet VPN) is used in a VXLAN fabric to distribute MAC address reachability information between switches. In this scenario, Switch 1 uses BGP EVPN to advertise the locally learned MAC addresses to Switch 2. This distribution of MAC addresses enables the switches to build and maintain an efficient forwarding table, facilitating communication across the VXLAN fabric.References:* Dell Technologies SONiC documentation* BGP EVPN Configuration GuideQUESTION 28Refer to the exhibit.The router ID has not been manually configured. What router ID is used for Switch 3?  192.168.100.2  192.168.100.0  10.0.2.1  10.0.1.1 In the absence of a manually configured router ID, OSPF typically uses the highest IP address on the switch’s active interfaces. For Switch 3 in the exhibit, the highest IP address is 10.0.1.1 on Loopback 0. Therefore,10.0.1.1 is used as the router ID for Switch 3.References:* Dell Technologies SONiC documentation* OSPF Configuration GuideQUESTION 29What does show interface breakout port slot/slot command display?  The Error/Debug status of the breakout of the port  The breakout modes available to that port  The In Progress/Complete status of the breakout of the port  The configuration of that port The show interface breakout port slot/slot command displays the breakout modes available for the specified port. Breakout modes determine how a single high-speed port can be split into multiple lower-speed ports, providing flexibility in network port configurations.References:* Dell Technologies SONiC Command Reference Guide* Port Breakout Configuration Guide Loading … Sample Questions of D-SNC-DY-00 Dumps With 100% Exam Passing Guarantee: https://www.examcollectionpass.com/EMC/D-SNC-DY-00-practice-exam-dumps.html --------------------------------------------------- Images: https://free.examcollectionpass.com/wp-content/plugins/watu/loading.gif https://free.examcollectionpass.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2024-10-18 14:22:18 Post date GMT: 2024-10-18 14:22:18 Post modified date: 2024-10-18 14:22:18 Post modified date GMT: 2024-10-18 14:22:18