300-510 PDF Pass Leader, 300-510 Latest Real Test [Q51-Q70]

300-510 PDF Pass Leader, 300-510 Latest Real Test

Valid 300-510 Test Answers & 300-510 Exam PDF

Audience, Prerequisites, and Objectives for Implementing Cisco Service Provider Advanced Routing Solutions Training

Particularly, this course for exam 300-510 invigorates the needs of network administrators, project managers, system engineers, and network designers. The initial requirements they need to meet before undertaking the training are such as having at least intermediate knowledge covering Cisco IOS or Cisco IOS XE as well as Cisco IOS XR Software that touches on the configuration. More requirements include awareness of networking concerning IPv6 and IPv4 TCP/IP, intermediate knowledge about routing protocols of OSPF, BGP, and ISIS, and comprehension regarding MPLS technologies, multicast technologies, and segment routing. Also, there are other vital courses that one ought to have passed through before this specific training. This is to gain the proper perspective about what they are about to learn and ensure this goes on effectively. Overall, on completing this 300-510 exam course, you will have mastered the following objectives:

• Using IPv6 mechanisms for tunneling;
• Implementing enhanced PIM-SM associated features;
• Troubleshooting ISIS, OSPF, and BGP;
• Implementing and troubleshooting traffic engineering for MPLS;
• Putting into practice mechanisms targeting dynamic RP (Rendezvous Point) distribution.
• Executing MSDP within the interdomain surrounding;
• Describing and comparing core concepts for multicast;
• Abilities in configuring route redistribution;
• Configuring BGP scalability within SP networks;
• Putting into operation and authenticating the protocol known as PIM-SM;
• Deploying and verifying MPLS;
• Capabilities in executing advanced features concerning multilevel ISIS that run in SP networks;
• Describing the usage of traffic engineering within networks for segment routing;

The skills covered when practicing with the hands-on labs for exam 300-510 include executing Special Area Types for OSPF, implementing Multiarea IS-IS, route redistribution, route selection for BGP, route reflectors, security options for BGP, and troubleshooting routing protocols. Others are executing MPLS within the SP core, deploying MPLS TE for Cisco, configuring and authenticating segment routing for IGP, and operating with tunnels aimed at IPv6. Candidates will also draw practical skills in the areas of enabling and optimizing PIM-SM, executing enhancements for PIM-SM, and putting into practice RP distribution.

Who should take the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam

People who wish to explore the power of the dynamic culture of the Cisco Learning Network to jump-start their certification and lifelong learning goals should take this exam. Those who want to get useful tools for IT training for all Cisco certifications should also get this certification. People with prior knowledge of integrating VPN services, including Layer 2, Layer 3, and IPv6, from the service provider are highly recommended to take this exam and get themselves certified from Cisco.

List of the target audience for this exam:

• Network managers
• Network engineers
• Channel partners
• Network administrators
• Network Operations Center (NOC) personnel
• Network architects
• Network supervisors

NO.51 What are two features of dual-stack? (Choose two.)

 It is implemented without excessive processing power.

 It supports IPv4 and IPv6 traffic on the same infrastructure.

 It allows an engineer to stack multiple Layer 2 switches to serve as a single switching unit.

 It requires tunneling IPv6 traffic over an IPv4 infrastructure.

 It securely routes and tunnels traffic between separate sites over the Internet.

NO.52 Refer io the exhibit.

While applying the configurations on two routers an engineer notices that OSPF adjacency Between them remains down Through the ping test the engineer confirmed that both me routers have Layer 3 reachability between them Which action should me engineer take to make the adjacencies to full?

 Enter the command ip ospf authentication in R2 interface

 Enable OSPF just inside the router OSPF process not in the interfaces of any router

 Delete the area 0 authentication message-digest command from the OSPF process in R1

 Delete the area 0 authentication message-digest command from the OSPF process in R2

NO.53 Refer to the exhibit.

An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?

 Router 1 sends and receives multiple best paths from neighbor 192.168.1.1

 Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes

 Router 1 sends only one best path to neighbor 192 168.1.1.

 Router 1 receives only one best path from neighbor 192.168.1.1

NO.54 Which two characteristics unique to SSM when compared to ASM are true? (Choose two.)

 It uses SPT switchover

 It uses (*,G) exclusively

 It uses IGMPv3

 It uses RP

 It uses (S,G) exclusively

NO.55 Referring to the topology diagram show in the exhibit, which three statements are correct regarding the BGP routing updates? (Choose three.)

 The EBGP routing updates received by R1 from R5 will be propagated to the R2, R4, and R7 routers

 The EBGP routing updates received by R3 from R6 will be propagated to the R2 and R4 routers

 The EBGP routing updates received by R1 from R5 will be propagated to the R2 and R4 routers

 The IBGP routing updates received by R3 from R2 will be propagated to the R6 router

 The IBGP routing updates received by R2 from R1 will be propagated to the R3 router

 The IBGP routing updates received by R1 from R4 will be propagated to the R5, R7, and R2 routers

NO.56 Refer to the exhibit.


Refer to the exhibit. A network engineer is investigating a report of packet drops between the branch site and the central site.
The two sites are connected via OSPF and RSVP-TE tunnels.
Traffic from the central site to the branch site is passing normally.
Technicians at both sites successfully ping the loopback IP addresses on routers R1 and R2.
Which configuration corrects the packet-drop problem?

 Option A

 Option B

 Option C

 Option D

NO.57 Refer to the exhibit.

Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?

 It must be configured for graceful restart

 It must be configured with a route reflector

 It must be configured with send labels

 It must be configured with PIC edge

NO.58 What is one of the configuration errors within an AS that can stop a Cisco IOS-XR router from announcing certain prefixes to its EBGP peers?

 Some prefixes were mistagged with the no-export BGP community

 Some prefixes were set with an MED of 0

 The outbound BGP route policy only has set actions defined without any pass actions defined

 The inbound BGP route policy only has set actions defined without any pass actions defined

NO.59

Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

 R5

 R3

 R4

 R2

NO.60 Refer to the exhibit.

How are packets directed through the data plane when SRv6 is implemented?

 An ordered list of segments is encoded in a routing extension header

 The MPLS data plane is used to push labels onto IGP routes

 A stack of labels represents an ordered list of segments

 The packet is encapsulated with a header and trailer encoding the ordered list of segments

NO.61 After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1
2/6 (unacceptable hold time) 0 bytes
Which action makes the peering come back up again?

 Make a soft reset to the peer.

 Set up a minimum hold-down timer higher.

 Set up a hello timer higher.

 Set up a hold-down timer higher.

NO.62 The core routers within a transit AS are running both IBGP and IGP. The edge routers within the transit AS are using the next-hop-self option to establish the IBGP sessions. What can be implemented to improve the routing performance to all external prefixes?

 enable route redistribution from BGP into IGP

 disable BGP synchronization on all the core routers

 enable CEF on all the core and edge routers

 enable route redistribution from IGP into BGP

 use route reflectors within the core

NO.63

Refer to the exhibit. After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

 Router 2 receives a Type 5 LSAs from router 1 for its connected subnets

 Router 2 uses router 3 as the next hop for 192.168.0.0/24

 Router 2 uses router 1 as the next hop for 192.168.0.0/24

 Router 2 receives a Type 7 LSAs from router 3 for its connected subnets

NO.64 Refer to the exhibit.

Which LSA type is indicated by this router output?

 type 3 LSA

 type 4 LSA

 type 1 LSA

 type 2 LSA

NO.65 Which difference should be considered when intradomain or interdomain multicast routing is implemented?

 Interdomain multicast routing requires an IS-IS or OSPF neighbor relationship between the domains but intradomain multicast routing requires only BGP Questions & Answers PDF P-57

 Interdomain multicast routing relies on PIM-DM and intradomain multicast routing relies on PIM- SM.

 interdomain multicast routing uses BIDR-PIM to establish neighbor relationships between AS and interdomain multicast routing uses MSDP

 A network uses intradomain multicast routing without interdomain routing but networks that use interdomain multicast routing must also apply intradomain routing

NO.66 Refer to the exhibit. After configuring IS-IS on routers R1 and R2, an engineer notices that only the loopback interface at 2000:1::1 /96 is known to router R2. Which change must be made so that only Loopback2 is advertised from R1 to R2?

 Configure the router isis area1 command under the Loopback0 interface on R1.

 Remove the advertise passive-only command under the IS-IS address family ipv6 configuration

 Remove the ipv6 router isis area1 command under the Loopback2 interface on R1.

 Remove the passive-interface Loopback0 command under the router isis area1 configuration.

NO.67 Refer to the exhibit. A network engineer implemented this segment routing configuration. Which statement about the output is true?

 This range conflicts with the segment routing local block range.

 The device must be reloaded for these ranges to be allocated and used.

 The default segment routing global block range is being used on this device.

 A nondefault segment routing global block range is being used on this device.

https://www.cisco.com/c/en/us/td/docs/routers/asr920/configuration/guide/segment-routing/ segment-routing-book/seg-routing-global-block.html

NO.68 Refer to the exhibit.

A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?

 Option A

 Option B

 Option C

 Option D

NO.69 Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?

 ip pim bidir-enable

 ipv4 pim bidir-enable

 ip multicast-routing

 ip pim bidir

Reference:
imc_basic_cfg.html

NO.70 A network engineer is troubleshooting OSPF multiare A.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?

 hierarchical CLI

 DR support for topology management

 routing process enabled by default on all interfaces

 show ip ospf topology command

OSPF Hierarchical CLI and CLI Inheritance
Hierarchical CLI is the grouping of related network component information at defined hierarchical levels such as at the router, area, and interface levels.
Hierarchical CLI allows for easier configuration, maintenance, and troubleshooting of OSPF configurations.
When configuration commands are displayed together in their hierarchical context, visual inspections are simplified. Hierarchical CLI is intrinsic for CLI inheritance to be supported.
With CLI inheritance support, you need not explicitly configure a parameter for an area or interface. In the software, the parameters of interfaces in the same area can be exclusively configured with a single command, or parameter values can be inherited from a higher hierarchical level-such as from the area configuration level or the router ospf configuration levels.
More information: https://www.cisco.com/c/en/us/td/docs/iosxr/ncs5500/routing/71x/b-routing-cg-ncs5500-71x/b-routing-cg-ncs5500-71x_chapter_011.html#con_1059437
Reference: guide/rc40xr12k_chapter4.html#con_1059437

 Loading …

Test 300-510, also referred to as SPRI, is a Cisco exam that is about the execution of advanced solutions for routing for Service Providers. Someone who passes it ends up with the Cisco Certified Specialist – Service Provider Advanced Routing Implementation certificate, which is specific only to this test. The other main certificate achieved upon nailing 300-510 as well is the CCNP Service Provider.

300-510 Dumps Ensure Your Passing: https://www.examcollectionpass.com/Cisco/300-510-practice-exam-dumps.html