H12-831_V1.0 Tested & Approved HCIP-Datacom Study Materials [Q91-Q107]

Q91. As shown in the figure, MPLS/BGP IPVPN is deployed on the network.
The MP-BGP neighbor relationship is established between PE1 and PE2 through the LoopbackD interface.
After the configuration is complete, it is found that CE1 and CE2 cannot learn routes from each other.
Run the command to check the error on PE2.
The neighbor information is shown in the figure, what is the most likely cause of the problem?

Q92. When configuring the DHCP Relay function on the device, the VLAN ANIF interface of the relay connection client must be bound with a DHCP server group, and the IP address of the proxy DHCP server must be configured in the bound DHCP server group.

Q93. On the 05PFv3 network shown in the figure, each interface of R1 and R2 has two IPv6 addresses. Although the IPv6 address prefixes of R1 and R2 are different, they can still be used to establish an OSPFv3 neighbor relationship. If R2 is the DR, the Intra-Area-Prefix-LSA generated by R2 contains four prefixes.

Q94. As shown below:

IR2] ad 2000
[R2-ad-basic-2000]rule deny
[R2-ad-basic-2000]quit
#
[R2] ospf
[R2-ospf-1]area 1
[R2-ospM-area-0.0.0.1] filter 2000 import
[R2-ospf-1-area-0.0.0,1] quit
[R2-ospf-1] default-route-advertise always

Q95. If display current-configuration can reach the setting of !JIS-IS, and display saved- There is no IS-IS setting in the configuration, so that means?

Q96. As shown in the figure, on the R1 router, network administrator A sends the routing entry to R2 through the routing policy After modifying the Local Preference value, you can control the path of traffic leaving the AS100

Q97. On the OSPFv3 network shown in the figure, OSPFv3 is enabled on the interfaces connecting R1, R2, and R3. The router ID of each router is 10.0.X.X, where X is the number of the router.
If you check detailed information about an LSA on R3, the command output shows that R1 and R2 are DRs on the network.
Options:

Q98. On the network shown in the figure, SW3 is the user gateway and DHCP relay agent.
The administrator plans to configure DHCP snooping on SW3 to prevent DHCP attacks.

Which of the following commands does not need to be configured on SW3?

Q99. IS-IS LSP fragments are identified by the LSP Number field in their LSP IDs. This field is 4 bits long.
Therefore, an IS-IS process can generate a maximum of 256 LSP fragments, which means only a limited amount of information can be carried. By adding additional system IDs, you can enable the IS-IS process to generate more LSP fragments.
Options:

Q100. For high reliability purposes, the following LDP messages are transmitted through TCP: discovery messages, session messages, advertisement messages, and notification messages.

Q101. On the OSPFv3 network shown in the figure, area 1 is a stub area, area 2 is a common area, and area 3 is an NSSA. Which of the following LSAs is displayed only in area 2?

Q102. From this picture, we can judge

Q103. What is the purpose of configuring LSP fragmentation on an IS-IS device?

Q104. A network engineer enters dir on the device to obtain the following file names. Which is most likely to be the version file of the device?

Q105. Senior engineers with rich experience can quickly solve faults only by relying on experience, and the efficiency is very high.

Q106. When a fault occurs, the fault can be classified to reduce the scope of fault location. Which of the following is not an interface configuration fault?

Q107. On an enterprise network shown in the figure, EBGP is deployed between CEs and PEs.
CE1 sends a VPN route to PE1.

Which of the following statements are false?
Options: