Check the Available 350-501 Exam Dumps with 373 QA's UPDATED 2023 [Q218-Q242]

4/5 - (1 vote)

Check the Available 350-501 Exam Dumps with 373 QA’s UPDATED 2023

Download 350-501 Exam Dumps Questions to get 100% Success in Cisco

Cisco 350-501 certification exam consists of multiple-choice questions that test the knowledge and skills of the candidates in various areas of service provider network core technologies. 350-501 exam covers topics such as network architecture and design, virtualization, automation, network assurance, security, and services. 350-501 exam is designed to test the candidates’ ability to design and deploy service provider networks, troubleshoot network issues, and ensure network security.

Cisco 350-501 exam consists of 90-110 multiple-choice, drag-and-drop, and simlet questions. 350-501 exam can be taken in English or Japanese and lasts for 120 minutes. To pass the exam, candidates require a score of at least 80%, and the certification is valid for three years.

Q218. Refer to the exhibit:

With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.1

192.168.0.3

192.168.0.4

192.168.0.5

Q219. Refer to the exhibit.

What is the result of this configuration?

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authorization.

Router 1 and the TACACS+ server maintain one open connection between them only when network administrator is accessing the router with password ciscotest.

Router 1 and the TACACS+ server maintain one open connection between them.

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authentication.

Q220. Refer to the exhibit. Which condition must be met by the OSPF peer of router R1 before the two devices can establish communication?

The interface on the OSPF peer must use the same key ID and key value as the configured interface

The interface on the OSPF peer may have a different key ID, but it must use the same key value as the configured interface

The OSPF peer must be configured as an OSPF stub router

The OSPF peer must use clear-text authentication

Q221. Refer to the exhibit. Which configuration prevents the OSPF neighbor from establishing?

mtu

duplex

network statement

default-metric

Q222. How much must the MTU be increased when configuring the 802.1q VLAN tag?

2 bytes

4 bytes

8 bytes

12 bytes

Q223. An engineer is implementing MPLS to monitor within the MPLS domain. Which must the engineer perform to prevent packets from being forwarded beyond the service provider domain when the LSP is down?

Option A

Option B

Option C

Option D

Q224. Refer to the exhibit. A network operator needs to shut down interface Gi0/0/0/2 for maintenance.
What occurs to the interface states of Gi0/0/0/0 and Gi0/0/0/1?

Gi0/0/0/1 and Gi0/0/0/0 become active

Gi0/0/0/1 and Gi0//0/0 remains standby

Gi0/0/0/0 becomes active. Gi0/00/1 remains standby

Gi0/0/0/1 becomes active Gi0/0/0/0 remains standby

Q225. Refer to the exhibit:

Which three outcomes occur if the prefix list is added to the neighbor? (Choose three)

192.168 0.0/19 is denied.

192.168 0.0/17 is denied.

192.168 0.0/17 is permitted

192.168.0.0/16 is denied

192.168 0.0/16 is permitted

192.168 0.0/19 is permitted

Q226. Refer to the exhibit.

A network engineer is implementing OSPF multiare
a. Which command on interface GO/1 resolves adjacency issues in the new area?

ip ospf network broadcast

ip ospf network point-to-point

ip ospf network non-broadcast

ip ospf network point-to-multipoint

Q227. Refer to the exhibit. A network engineer is implementing an OSPF configuration Based on the output, which statement is true?

In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.

OSPFv3 does not run for IPv4 on FastEthernet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface FastEthernet0/0.

OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.

IPv6 routing not enabled” is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway

Q228.

Refer to the exhibit. A network engineer is implementing a standard customer route-policy on router ASBR1 with these requirements:
* It must accept only customer-assigned prefixes.
* It must preserve customer-advertised BGP communities.
* It must set the local-preference to 110 for all prefixes.
* It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes.
Which route policy must the engineer implement on ASBR1 to satisfy the requirements?

Q229. How is a telemetry session established for data analytics?

A router initiates a session using the dial-out mode to a destination.

A destination initiates a session to a router.

The destination Initiates a session using the dial-out mode to the router.

A router requests the data using Telnet.

Q230. After a series of unexpected device failures on the network, a Cisco engineer is deploying NSF on the network devices so that packets continue to be forwarded during switchovers. The network devices reside in the same building, but they are physically separated into two different data centers. Which task must the engineer perform as part of the deployment?

implement OSPF to maintain the link-state database during failover.

implement VRFs ana specify the forwarding instances that must remain active during failover.

implement an L2VPN with the failover peer to share state Information between the active and standby devices.

implement Cisco Express Forwarding to provide forwarding during failover

Q231. Refer to the exhibit. The network engineer who manages ASN 65001 is troubleshooting suboptimal routing to the 198.18.15.0/24 prefix. According to the network requirements:
– Routing to IP destinations in the 198.18.15.0/25 block must be
preferred via the EDGE-1 PE.
– Routing to IP destinations in the 198.18.15.128/25 block must be
preferred via the EDGE-2 PE.
– More specific prefixes of the 198.18.15.0/24 block must not be
advertised beyond the boundaries of ASN 64611.
– Routing to 198.18.15.0/24 must be redundant in case one of the
uplinks on INT-R1 fails.
Which configuration must the network engineer implement on INT-R1 to correct the suboptimal routing and fix the issue?

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-export, peeras:65001)
done
endif
if destination in (198.18.15.0/24) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (internal, peeras:65001)
done
endif
if destination in (198.18.15.0/24) then
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-advertise, peeras:65001)
done
endif
if destination in (198.18.15.128/25) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-export, peeras:65001)
done
endif
if destination in (198.18.15.128/25) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT in
end

Q232. Refer to the exhibit:

Which command is used to complete this configuration for QoS class-based marking?

PE-A(config-pmap-c)#set dscp ef

PE-A(config-pmap-c)#fair-queue

PE-A(config-pmap-c)#random-detect

PE-A(config -pmap-c)#priority

Q233. Refer to the exhibit.

CE1 and CE2 require connectivity to the internet through the ISP connected to PE3 What should an engineer configure to complete this task?

PE2 must be configured to serve as a route reflector for PE3 routes learned from the internet. PE2 then shares the routes with CE1 and CE2.

CE1 and CE2 must be configured with a route distinguisher in the PE1 VRF that dynamically imports the route from the internet.

CE1 and CE2 must be configured to use a static default route with a next-hop of PE3 to reach internet routes.

PE1 must be configured with an import route target in the CE1 VRF that matches the export route target for the internet VRF on PE3.

Q234. Refer to the exhibit. What is the purpose of this JSON script?

It changes the existing password.

It updates a user authentication record.

It deletes a user’s authentication record.

It confirms a user’s login credentials.

Q235. Which characteristic describes prefix segment identifier?

it contains the interface address of the device per each link.

It Is globally unique.

it is locally unique.

It contains a router to a neighbor.

Q236. Refer to the exhibit.

Which type of DDoS attack will be mitigated by this configuration?

SYN flood

smurf attack

SIP INVITE flood attacks

teardrop attack

Q237. Refer to the exhibit. With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.1

192.168.0.3

192.168.0.4

192.168.0.5

Q238. Refer to the exhibit:

Based on the show/ command output, which result m true after BGP session is established?

The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from 192.168.2.2

The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2

No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it

The IOS XR router does not advertise any routes to the neighbor 192.168.2.2,but it accepts all routes from 192.168.2.2.

Q239. Refer to the exhibit:

Which command is used to complete this configuration for QoS class-based marking?

PE-A(config-pmap-c)#set dscp ef

PE-A(config-pmap-c)#fair-queue

PE-A(config-pmap-c)#random-detect

PE-A(config -pmap-c)#priority

Q240. Drag and drop the functionalities from the left onto the correct target fields on the right.

Q241. Refer to the exhibit:

An engineer is preparing to implement link aggregation configuration.
Which statement al about this configuration is true?