[Sep-2023 Newly Released] Pass 300-510 Exam - Real Questions & Answers [Q48-Q72]

Rate this post

[Sep-2023 Newly Released] Pass 300-510 Exam – Real Questions and Answers

Pass 300-510 Review Guide, Reliable 300-510 Test Engine

Cisco 300-510 exam is a challenging but rewarding certification exam for professionals who want to enhance their skills in implementing advanced routing solutions in a service provider network. Passing 300-510 exam can help you stand out in the job market, increase your earning potential, and open up new career opportunities. With proper preparation and dedication, you can pass the exam and join the elite group of Cisco certified professionals.

NEW QUESTION 48
Refer to the exhibit. An engineer working on a client’s network is trying to solve the BGP community issue on R1 and R2 routers. After displaying the BGP entries, the engineer notices that both routers still have different outputs. Which action must the engineer perform to any of the routers to correct the problem and get the same output?

Execute the lp bgp-community new-format command in Router1.

Remove the lp bgp-community new-format command in Router1.

Advertise the route to Router2 as standard community.

Advertise the route to Router2 as extended community.

NEW QUESTION 49
In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?

The receiver explicitly requests its desired traffic from the RP on the shared tree.

The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.

The RP on the shared tree floods traffic out of all PIM configured interfaces.

The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.

NEW QUESTION 50
Refer to the exhibit.

P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which two actions fix the issue? (Choose two.)

Change MD5 to HMAC-SHA1-12

Change MD5 to HMAC-ESP

Change MD5 to SHA-1

Change MD5 to HMAC-MD5

Remove the send and accept lifetime under key 1

NEW QUESTION 51
Refer to the exhibit.

A network engineer implemented this segment routing configuration. Which statement about the output is true?

This range conflicts with the segment routing local block range.

The device must be reloaded for these ranges to be allocated and used.

The default segment routing global block range is being used on this device.

A nondefault segment routing global block range is being used on this device.

NEW QUESTION 52
Which difference must an engineer consider when choosing whether to implement OSPF or IS-IS as the routing protocol on the network?

The OSPF DR election process is deterministic, and the IS-IS DS election process is not deterministic.

To support fast convergence, OSPF uses the LSA arrival timer and IS-IS uses the PRC-interval timer.

IS-IS supports ordinary, stub, totally-stub, and NSSA areas, but OSPF supports only stub areas.

IS-IS links are associated with either a Level 1 area or a Level 2 area at one time, but OSPF links are associated with multiple areas at one time.

NEW QUESTION 53
An engineer is working to implement segment routing protocol on the customer’s core network. Which step should the engineer take before the segment routing is enabled and is running with BGP?

Segment routing must be configured with ISIS.

Segment routing must be configured with EIGRP.

Explicit-null must be configured for all neighbors.

MPLS must be configured.

NEW QUESTION 54
Refer to the exhibit.

Router 1 and Router2 have shared routes in the OSPF database but the routes are missing from their routing tables. Checking me prefix-list configuration on both routers, the engineer confirmed all networks are allowed What action should the engineer take to fa the problem?

Configure the two routers with different process IDs

Configure the two routers with different hello and dead timer values

Switch the DR and BDR roles between the two routers

Configure interface Senal1/0 on Router1 as a point-to-point interface

NEW QUESTION 55
Refer to the exhibit

Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?

NEW QUESTION 56
Refer to the exhibit.

R2

NEW QUESTION 57
Refer to the exhibit.

An engineer is addressing an IS-IS design issue which is running within the topology. All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet. Which statement about the design is true?

R4 prefer to reach R5 using R1 as the next hop

All links have equal cost if the default metric is used

R5 prefers to use R4 as the next hop for all routes

R1 prefer to use R5 as the next hop to reach R4

NEW QUESTION 58
Drag and drop the features from the left into the order of operations for SRv6 SSH field creation and forwarding on the right.

NEW QUESTION 59
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)

NEW QUESTION 60
Refer to the exhibit.

An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?

The MED attribute can be applied on R2 to influence R1 to use it as the primary path.

The local preference attribute can be applied on R3 to influence AS 65513 to use AS 65515 as the secondary path.

The weight attribute can be applied on R2 to influence AS 65513 to use AS 65515 as the primary path.

The IGP metric can be manipulated on R1 to allow traffic to be load balanced between R2 and R3.

NEW QUESTION 61
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time) 0 bytes Which action makes the peering come back up again?

Make a soft reset to the peer.

Set up a minimum hold-down timer higher.

Set up a hello timer higher.

Set up a hold-down timer higher.

NEW QUESTION 62
Refer to the exhibit.

While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?

Set up a priority different than 0 in the interface.

Modify the router ID to be the interface IP on the serial.

Modify the IP address or mask of the interface to a valid one.

Set the network type in S1/0 to point-to-point.

NEW QUESTION 63
Refer to the exhibit.

NEW QUESTION 64
A network engineer is troubleshooting OSPF multiare
a. Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?

hierarchical CLI

routing process enabled by default on all interfaces

DR support for topology management

show lp ospf topology command

NEW QUESTION 65
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time)
0 bytes
Which action makes the peering come back up again?

Make a soft reset to the peer.

Set up a minimum hold-down timer higher.

Set up a hello timer higher.

Set up a hold-down timer higher.

NEW QUESTION 66
What is enabled by default on Cisco IOS-XR routers and cannot be disabled?

SSH server

Multicast routing

IPv4 and IPv6 CEF

IPv6 routing

CDP

BFD

NEW QUESTION 67
While configuring Cisco NSF awareness, a network engineer enters the bgp graceful-restart command after the BGP session is established in a router that runs IOS XE Software. Graceful restart capabilities are not exchanged. Which two actions should be taken? (Choose two.)

Reload the router

Verify that BGP route dampening is configured

Reduce BGP convergence time

Issue the clear ip bgp * command

Issue the show ip bgp neighbors command.

NEW QUESTION 68
Drag and Drop Question
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues?
Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)

NEW QUESTION 69

Refer to the exhibit. A network engineer implemented this segment routing configuration. Which statement about the output is true?

This range conflicts with the segment routing local block range.

The device must be reloaded for these ranges to be allocated and used.

The default segment routing global block range is being used on this device.

A nondefault segment routing global block range is being used on this device.

NEW QUESTION 70
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.

NEW QUESTION 71
Refer to the exhibit. A network operator is troubleshooting TE tunnels and discovers that the soft preemption is not working as desired.
Where should the soft preemption be applied to solve the issue?

on the tail-end device for tunnel-te1 192.168.0.7

under the tunnel-te1 interface on PE1

explicitly for tunnel-te 1 under the Cisco MPLS TE configuration mode after the timeout setting

Under the interface Loopback0 necessary for this deployment type.

NEW QUESTION 72
Refer to me exhibit. A network engineer sets up a multihoming eBGP topology where multiple Autonomous Systems connect to ASN 64501.

The engineer wants to block all the routers coming from ASN 64502. but allow all the others. For that purpose, the following AS Pam prefix 1st s being used:
(config)#ip as-path access-list 10 deny _64502$
What must be fixed to achieve this result?

The AS-PATH filter must be defined inside the route-map mode

At the end ip as-path access-list 10 permit .* must be included

The statement must be modified with ip as-path access-list 1 deny _64502_

The statement must CM modified with ip as path access list 1 deny A64502$

Cisco 300-510 exam covers a wide range of advanced routing technologies, including Border Gateway Protocol (BGP), Multiprotocol Label Switching (MPLS), and Virtual Private Network (VPN) technologies. It also tests the candidate’s knowledge of advanced routing policies, route redistribution, and route filtering techniques. Successful candidates are expected to have a deep understanding of how these technologies work and how they can be configured and optimized in a service provider network.

100% Free 300-510 Daily Practice Exam With 177 Questions: https://www.examcollectionpass.com/Cisco/300-510-practice-exam-dumps.html