Get The Important Preparation Guide With HPE0-S60 Dumps [Q34-Q57]

Rate this post

Get The Important Preparation Guide With HPE0-S60 Dumps

Get Totally Free Updates on HPE0-S60 Dumps PDF Questions

HPE0-S60 exam is a valuable certification for IT professionals who work with HPE compute solutions. It validates their knowledge and skills in the latest HPE compute solutions and demonstrates their commitment to staying up-to-date with the latest technologies. Delta – HPE Compute Solutions certification is recognized by IT organizations around the world and can help professionals advance their careers and increase their earning potential. HPE0-S60 exam is also a prerequisite for the HPE Master ASE – Advanced Server Solutions Architect V3 certification.

NO.34 You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.
Put the steps to achieve this goal into the coned order in the answer area on the right.

NO.35 The proposal consists of.
– 3 HPE Synergy 12000 frames
– 6 HPE Composer 2 modules
– 2 HPE Virtual Connect SE 100 GO F32 Module
– 4 HPE Synergy 50 GO interconnect Link Module
Which statements about this proposed design are true? (Select two.)

The selected interconnect modules do not provide the requested WWN virtualization

HPE Synergy 50Gb ILMs must be replaced with HPE Virtual Connect SE 100 GO F32 modules

The current setup can support up to 18 HPE Synergy 480 Gen10 Plus compute modules

FC upgrade licenses for HPE Virtual Connect SE 100 GbF32 Module must be added

Remove 4 HPE Composer 2 modules from the design, as they are not required

NO.36 Which statement about a new HPE SimpliVity deployment is true?

New HPE SimpliVity deployments give customer flexible choice of hypervisor

All new HPE SimpliVity models are based on AMD CPUs

All new HPE SimpliVity models support deduplication and compression

New HPE SimpliVity deployments are licensed per node not per physical socket

NO.37 Which statement about HPE Superdome Flex 280 is true?

It supports 2 to 8 sockets in 2-socket increments.

it cannot be managed using HPE OneView.

It must be equipped with at least 768 GB of memory.

It can support up to two nPars with an external RMC.

NO.38 After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.

NO.39 Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.
What should you do to resolve this issue?

Disable deduplication for this volume at the array level

Remove the offline disks using array management tools

Install and configure MPIO on me Windows system

Remove the offline disks using Windows Disk Management

NO.40 Your customer has the following HPE Synergy setup
– 3 HPE Synergy 12000 Frames
– 4 HPE Virtual Connect SE 100 Gb F32 Modules
– 2 HPE Synergy 50 GO Interconnect Link Modules
– 36 HPE Synergy 480 Gen10 Plus compute modules
– 2 HPE Composer 2 modules
Which statement about this setup is true?

To use all compute nodes, the customer must create at least two logical enclosures

To manage all frames, the customer must buy two additional HPE Composer 2 modules

The customer must buy 36 HPE OneView Advanced licenses to manage compute modules

The customer can add one D3940 storage Module to each of the frames

NO.41 Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?

The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.

The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.

The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.

The customer can add a new logical enclosure to an existing setup once all required licenses are added lo HPE OneView and associated with the new frames.

NO.42 What is a restriction of using a RoCE network?

It is by default configured as an untagged network and cannot be a part of a network set.

It does not support Private VLAN and Multicast VLAN.

it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.

It does not support smart link and private network features.

NO.43 Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

NO.44 Which statement about a new HPE SimpliVity deployment is true?

New HPE SimpliVity deployments gives customer flexible choice of hypervisor

A new HPE SimpliVity node can be a member of multiple dusters

AM new HPE SimpliVity models are software optimized

All new HPE SimpliVity models are based on mid CPUs

NO.45 Your customer plans to expand an existing nPar based on a single HPE Superdome Flex chassis. Which statement about workload availability during expansion is true?

Powered nPar can be expanded only if HPE Superdome Flex 280 is used

Online expansion is available only if RMC is used for management.

HPE Superdome Flex does not support expansion of powered on nPars

Powered nPar can be expanded if it does not use HPE Persistent Memory

NO.46 Refer to the exhibit.

Which statement about this logical JBOD is true?

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

This logical JBOD can be presented to the compute nodes in a different frame.

NO.47 Match each HPE OneView network type with its definition.

NO.48 Match HPE Superdome Flex system with its specific feature.

NO.49 Which statement about HPE Apollo 2000 Gen10 Plus platform is true?

It is equipped with HPE Persistent memory by default

It can support a single processor only and up to 4 per chassis

It is fully managed using HPE OneView including all connections

It offers servers with AMD EPYC and Intel Xeon Scalable CPUs

NO.50 What is a limitation when creating a server profile?

BIOS settings can be changed only when UEFI optimized is selected as boot mode

ILO management is limited to the integration with Active Directory or LDAP

Administrator cannot define more than 8 connections within a server profile

It is not possible to create shared volumes on demand through a server profile

NO.51 Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

NO.52 Your customer has experience with utilization sampling for HPE Virtual Connect SE 100 Gb F32 Module for HPE Synergy. They have recently purchased HPE VC FC modules.
What must you be aware of regarding utilization sampling for the new modules?

Utilization sampling for HPE VC FC modules must be enabled manually using CLI.

For HPE VC FC modules, utilization sampling is always enabled and cannot be disabled

For HPE VC FC modules, utilization sampling can be enabled once appropriate license is applied

Utilization sampling works the same way tor any type of HPE Synergy interconnect modules

NO.53 Match each HPE OneView network type with its definition.

NO.54 An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement

NO.55 Your customer uses HPE OneView to manage their HPE Synergy environment. They plan to use it to manage a new set equipment that includes.
– 20 HPE ProLiant DL365 Gen10 Plus servers
– 20 HPE ProLiant DL380 Gen10 Plus servers
– 5 HPE Primera 650
– 5 HPE MSA 2062 Storage Array
Which statements about now OneView will work with this new equipment are true? (Select two)

HPE ProLiant DL365 Gen10 Plus servers are not supported in HPE OneView

HPE MSA 2062 Storage Array is not supported in HPE OneView

HPE OneView replaces array management tools for both types of array

HPE ProLiant DL380 Gen10 Plus servers have an HPE OneView license included

HPE Primera 650 can be managed using HPE OneView.

NO.56 Which statement about login redistribution is true?

NO.57 Your customer plans to deploy HPE Superdome Flex and configure two nPars, each based on two chassis Which components must be included in the proposal to meet the customer’s needs?

Rack Management Controller for nPar management

HPE Superdome Flex Grid licenses enabling connectivity between chassis

At least Tour HPE Persistent Memory DIMMs per nPar

One base chassis and three expansion chassis with licenses